Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Channelview, TX
Gate access control and welding repair in Channelview means dealing with what the Houston Ship Channel does to metal. We replace keypads, phone-entry modules, hinges, and gate posts in a community where airborne sulfur compounds pit steel hardware in three to five years, not fifteen. Work trucks and trailers sit behind decades-old swing gates on pier-and-beam lots, and when a post heaves after a flood, the gate binds and the opener strains. If your gate isn’t reading codes or the hinges are screaming, call (346) 423-6136 and we’ll put a name and a written price in front of you before any tool comes off the truck.
Why Channelview Homes Are Different
Channelview sits directly along the Ship Channel’s petrochemical corridor, and the air here carries hydrogen sulfide, sulfur dioxide, and other emissions that accelerate corrosion on steel and iron gates. We regularly see sulfide-pitted hinges and blackened latch hardware on gates that are only three to five years old, a failure mode you won’t find in Katy or Pearland. Stainless-steel hardware and marine-grade coatings aren’t an upsell in this zip code. They’re the difference between a two-year repair and a ten-year repair.
The housing stock compounds the problem. Channelview was built largely from the 1950s through the 1970s to house plant workers, which means modest ranch-style and pier-and-beam homes on larger lots. Residents store work trucks, trailers, boats, and equipment behind driveway gates, so the gates themselves are typically decades-old swing or slide designs with steel posts set in concrete. Then the floods come: Channelview sits low and takes water during heavy rain events. Footings heave, settle, and shift, throwing gate alignment off and binding automated operators. By the time a homeowner calls us, the gate has usually been dragging for weeks and the motor has been running hot.
Our Main Channelview Services
These are the three calls we get most from Channelview homeowners.
Gate Repair in Channelview
Repair work here almost always starts with corrosion or a shifted post. We find seized hinges, sagging leafs, and operators fighting a gate that no longer swings true. On a typical Channelview visit we photograph what we found, write down what we’re going to do, and hand you the price before work starts. Gate Repair in Channelview covers swing gates, slide gates, latches, wheels, and alignment work across every neighborhood in the area.
Gate Installation in Channelview
New gates in Channelview need to be spec’d for the air, not just the opening. We recommend marine-grade primers and stainless hardware on everything we install within a couple miles of the refineries, and we set posts deeper than code minimums because the ground here moves. Gate Installation in Channelview walks through what a full install costs, how we handle the old gate, and what kind of operator we’d pair with it.
Gate Motor & Opener in Channelview
Motors in Channelview don’t live easy. The chemically-laden air shortens the life of control boards and limit switches, and the heat gets to capacitors faster than in inland suburbs. When an opener fails here, we check the gate’s physical alignment first, because a dragging gate is often what killed the motor. Gate Motor & Opener in Channelview covers diagnostics, board replacement, and full operator swaps on whatever brand is already on the post.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Channelview
Access control in Channelview means keypads, phone-entry systems, card readers, and video intercoms that have to survive sulfide-heavy air and Gulf Coast humidity while controlling a gate that may sit on a shifting post. We’ve rebuilt more than a few Channelview keypads whose housings looked fine on the outside and were full of corrosion on the inside, because the seals failed two years in and nobody noticed until the buttons stopped responding. When that happens, the gate either won’t open or won’t close for code, and a house full of work trucks sits stuck behind a dead panel. Our work falls under Gate Access Control: diagnose the device, document what we found, fix or replace it, and leave you a photo record of the wiring and the new unit installed.
Keypad Entry
Signs you need it
The keypad beeps but doesn’t trigger the gate, certain codes stop working, or the housing shows white corrosion powder around the seal.
What it costs in Channelview
Replacing a residential keypad in Channelview typically runs $180 to $450 installed, depending on whether it’s a standalone unit or tied into a larger access-control board.
How we do it
We open the housing, photograph the wiring and any corrosion, test the circuit with a meter, and replace the unit with a sealed model rated for coastal air before reprogramming your codes.
Phone Entry
Signs you need it
Visitors call the intercom and get no dial tone, the gate won’t open from the app or a phone call, or the unit works intermittently after rain.
What it costs in Channelview
Phone-entry system repair in Channelview usually lands between $350 and $1,300 depending on whether we’re replacing a cell unit, a wired phone board, or the entire intercom housing.
How we do it
We test the phone module, check the power supply and antenna, replace the failed part, and re-verify all programmed numbers before sealing the housing against Channelview’s humid air.
What Gate Access Control Costs in Channelview
| Item | Typical range in Channelview |
|---|---|
| Keypad replacement | $180 - $450 installed |
| Phone-entry system repair | $350 - $1,300 |
| Video intercom upgrade | $650 - $2,000+ |
Can you fix a keypad that’s gone dead from Channelview’s air?
Yes. We diagnose whether the corrosion killed the board or just the contacts, photograph what we find, and replace the failed component rather than the whole system when repair is cheaper. Call (346) 423-6136 and we’ll give you a written price before starting.
Do you install phone entry on older Channelview gates?
We do. We’ve put phone-entry modules on 1960s swing gates and modern slide gates alike, and we wire them so the existing safety edges and photo-eyes still interrupt the gate properly. A free estimate is a phone call away.
Gate Parts & Welding in Channelview
Welding and parts work in Channelview is about repairing metal that the air has eaten and the ground has moved. We replace hinges that have seized from sulfide pitting, weld cracks in steel frames that flexed when a post shifted, and rebuild gate rollers that haven’t turned freely in years. Homeowners here run older gates harder than most of Houston, because bigger lots and stored equipment mean the gate cycles more times per day. That’s the kind of work covered under Gate Parts & Welding: cut out the failed steel, weld in a replacement, and leave the gate swinging true with a photo record of every seam.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinges squeal or show orange rust streaks, or you can see visible sag at the free end.
What it costs in Channelview
Hinge replacement for a typical Channelview driveway gate runs $180 to $520 including new stainless or marine-coated hinges, gussets, and alignment work.
How we do it
We lift and brace the gate leaf, cut out the old hinges, weld in new ones, and align the gate so it closes on the latch instead of fighting it.
Post Replacement
Signs you need it
The gate post leans, the concrete around its base is cracked, or the gate suddenly starts binding after a heavy rain event.
What it costs in Channelview
Replacing a shifted or rotted gate post in Channelview costs between $450 and $1,100 depending on post size, concrete depth, and whether the operator arm needs re-mounting.
How we do it
We dig out the old post and footing, set a new steel post in fresh concrete below the frost line and flood-saturation depth, and re-hang the gate level and plumb.
What Gate Parts & Welding Costs in Channelview
| Item | Typical range in Channelview |
|---|---|
| Hinge replacement | $180 - $520 |
| Post replacement | $450 - $1,100 |
| Custom welding repair | $120 - $400 per seam |
Can you weld a crack in my gate frame without replacing the whole gate?
Usually yes. We grind out the crack, weld it solid, and add a gusset plate where the frame flexed, then photograph the repair. We’ll only recommend replacement when the surrounding metal measures too thin to weld safely.
Do you stock stainless hinges for Channelview’s corrosive air?
We carry stainless and marine-coated hardware on the truck for Channelview jobs, because standard zinc-plated hinges don’t survive this air. Call (346) 423-6136 and we’ll tell you what’s on the shelf for your gate.
Brands We Service in Channelview
We service LiftMaster, FAAC, Mighty Mule, and Elite openers in Channelview, along with five other major automation brands. We keep common boards, remotes, and safety-edge components stocked locally, so most motor and access-control repairs get a same-week fix rather than a two-week parts wait. See our brands for the full list.
Pricing for Gate Repair in Channelview, TX
| Service | Typical range in Channelview |
|---|---|
| Keypad replacement | $180 - $450 installed |
| Phone-entry system repair | $350 - $1,300 |
| Video intercom upgrade | $650 - $2,000+ |
| Card reader installation | $300 - $900 |
| Hinge replacement | $180 - $520 |
| Post replacement | $450 - $1,100 |
| Custom welding repair | $120 - $400 per seam |
| Gate roller replacement | $150 - $380 |
Prices in Channelview push toward the upper end when corrosion has spread beyond the visible damage, when a post has to be re-set because flood-saturated soil moved it, or when the gate is heavy enough that we need a lift to get it off the hinges. Every job gets a written price before we start, so the number on the invoice matches the number on the paper you already approved.
Neighborhoods We Serve in Channelview
We work across the entire Channelview area, from the older neighborhoods near the Ship Channel up through the newer subdivisions off Sheldon Road. Response time for most locations in Channelview is under an hour when we have a crew in the area, and we schedule exact windows rather than four-hour blocks.
- Old River Terrace
- Cloverleaf (east side)
- Sheldon Woods
- Channelview proper along Market Street
- Portland and the streets around the high school
Service Area - Cities Near Channelview
Our Channelview crews also cover the surrounding Harris County communities where the same Ship Channel air and flood-plain soil shape the gate work. We serve Highlands, TX to the east, Galena Park, TX to the west, Houston, TX for jobs inside the broader metro, and Humble, TX to the north.
Serving Channelview, TX - Our Local Coverage Area
We’re based in the Channelview area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Channelview
When we have a crew in the area, most Channelview calls get a technician on-site in under an hour. Emergency calls are answered by a live person 24/7, and you’ll get a written price before any work begins rather than an estimate after we’ve already started.
Channelview is unincorporated Harris County, so permits generally aren’t required for gate repair or for replacing an existing gate on the same posts. New installations with new post footings may need a county permit depending on the scope, and we’ll tell you before you commit.
Yes. Properties within a mile or two of the Ship Channel show sulfide pitting and blackened hardware on gates that are only three to five years old. We recommend stainless-steel hardware and marine-grade coatings on most Channelview jobs, not as an upgrade but as the only hardware that lasts.
If your gate is binding, sagging, or ignoring the keypad, call (346) 423-6136. We’ll put a written price in your hand before any work starts and leave you with a photo record of everything we touched.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Channelview Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.